Layer 2 vs Layer 3 Ethernet Interface Possible Configuration

Layer 2

SWITCH_TPM(config)#int faste 0/1
SWITCH_TPM(config-if)#?
Interface configuration commands:
  arp                     Set arp type (arpa, probe, snap) or timeout
  bandwidth               Set bandwidth informational parameter
  carrier-delay           Specify delay for interface transitions
  cdp                     CDP interface subcommands
  custom-queue-list       Assign a custom queue list to an interface
  default                 Set a command to its defaults
  delay                   Specify interface throughput delay
  description             Interface specific description
  duplex                  Configure duplex operation.
  exit                    Exit from interface configuration mode
  fair-queue              Enable Fair Queuing on an Interface
  help                    Description of the interactive help system
  hold-queue              Set hold queue depth
  keepalive               Enable keepalive
  load-interval           Specify interval for load calculation for an
                          interface
  logging                 Configure logging for interface
  loopback                Configure internal loopback on an interface
  mac-address             Manually set interface MAC address
  max-reserved-bandwidth  Maximum Reservable Bandwidth on an Interface
  media-type              Interface media type
  mtu                     Set the interface Maximum Transmission Unit (MTU)
  negotiation             Select Autonegotiation mode
  no                      Negate a command or set its defaults
  port                    Perform switch port configuration
  priority-group          Assign a priority group to an interface
  random-detect           Enable Weighted Random Early Detection (WRED) on an
                          Interface
  rmon                    Configure Remote Monitoring on an interface
  service-policy          Configure QoS Service Policy
  shutdown                Shutdown the selected interface
  snmp                    Modify SNMP interface parameters
  spanning-tree           Spanning Tree Subsystem
  speed                   Configure speed operation.
  switchport              Set switching mode characteristics
  timeout                 Define timeout values for this interface
  transmit-interface      Assign a transmit interface to a receive-only
                          interface
  tx-queue-limit          Configure card level transmit queue limit
  udld                    Configure UDLD enabled or disabled and ignore global
                          UDLD setting



Layer 3

gwsoclab(config)#int faste 0/1
gwsoclab(config-if)#?
Interface configuration commands:
  access-expression       Build a bridge boolean access expression
  appletalk               Appletalk interface subcommands
  arp                     Set arp type (arpa, probe, snap) or timeout
  auto                    Configure Automation
  backup                  Modify backup parameters
  bandwidth               Set bandwidth informational parameter
  bgp-policy              Apply policy propagated by bgp community string
  bridge-group            Transparent bridging interface parameters
  carrier-delay           Specify delay for interface transitions
  cdp                     CDP interface subcommands
  clns                    CLNS interface subcommands
  cmns                    OSI CMNS
  crypto                  Encryption/Decryption commands
  custom-queue-list       Assign a custom queue list to an interface
  dampening               Enable event dampening
  decnet                  Interface DECnet config commands
  default                 Set a command to its defaults
  delay                   Specify interface throughput delay
  description             Interface specific description
  dlsw                    DLSw interface subcommands
  dot1q                   dot1q interface configuration commands
  dot1x                   Interface Config Commands for 802.1x
  dspu                    Down Stream PU
  duplex                  Configure duplex operation.
  eou                     EAPoUDP Interface Configuration Commands
  exit                    Exit from interface configuration mode
  fair-queue              Enable Fair Queuing on an Interface
  flow-sampler            Attach flow sampler to the interface
  fras                    DLC Switch Interface Command
  full-duplex             Configure full-duplex operational mode
  glbp                    Gateway Load Balancing Protocol interface commands
  half-duplex             Configure half-duplex and related commands
  help                    Description of the interactive help system
  hold-queue              Set hold queue depth
  ip                      Interface Internet Protocol config commands
  ipv6                    IPv6 interface subcommands
  ipx                     Novell/IPX interface subcommands
  isis                    IS-IS commands
  iso-igrp                ISO-IGRP interface subcommands
  keepalive               Enable keepalive
  lan-name                LAN Name command
  lat                     LAT commands
  llc2                    LLC2 Interface Subcommands
  load-interval           Specify interval for load calculation for an
                          interface
  locaddr-priority        Assign a priority group
  logging                 Configure logging for interface
  loopback                Configure internal loopback on an interface
  mac-address             Manually set interface MAC address
  max-reserved-bandwidth  Maximum Reservable Bandwidth on an Interface
  mls                     mls sub/interface commands
  mop                     DEC MOP server commands
  mpoa                    MPOA interface configuration commands
  mtu                     Set the interface Maximum Transmission Unit (MTU)
  netbios                 Use a defined NETBIOS access list or enable
                          name-caching
  no                      Negate a command or set its defaults
  ntp                     Configure NTP
  pppoe                   pppoe interface subcommands
  pppoe-client            pppoe client
  priority-group          Assign a priority group to an interface
  random-detect           Enable Weighted Random Early Detection (WRED) on an
                          Interface
  rate-limit              Rate Limit
  routing                 Per-interface routing configuration
  sap-priority            Assign a priority group
  service-policy          Configure QoS Service Policy
  shutdown                Shutdown the selected interface
  sna                     SNA pu configuration
  snapshot                Configure snapshot support on the interface
  snmp                    Modify SNMP interface parameters
  speed                   Configure speed operation.
  standby                 HSRP interface configuration commands
  tarp                    TARP interface subcommands
  timeout                 Define timeout values for this interface
  traffic-shape           Enable Traffic Shaping on an Interface or
                          Sub-Interface
  transmit-interface      Assign a transmit interface to a receive-only
                          interface
  tx-ring-limit           Configure PA level transmit ring limit
  vlan-id                 Process VLAN-encapsulated packets with a specific
                          VLAN ID
  vlan-range              Process VLAN-encapsulated packets with a range of
                          VLAN IDs
  vrrp                    VRRP Interface configuration commands
  xconnect                Xconnect commands

gwsoclab(config-if)#